When you would install a new item, you should not forget the steps as to how it will be placed. You should follow them so you can correctly install any Profile Design Cobra bars. This has been required on the policies of its warranty which will be given to the buyer. If you have no knowledge on this, you can ask for help from a dealer nearby.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
0 comments:
Post a Comment